Buy ASTM D Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils from SAI Global. GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Consolidated Undrained Triaxial Compression Test for . Consolidated Undrained Triaxial Compression Test for Cohesive Soil.
|Published (Last):||13 June 2013|
|PDF File Size:||16.24 Mb|
|ePub File Size:||9.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
Triaxial cells for advanced applications The cell essentially consists of a trasparent ast, chamber to prevent excessive expansion during the test and to protect against explosive failure when used with compressed air systems.
ASTM D, Test equipment Controls
Note 2—Notwithstanding the statements on precision and bias contained in this test method. Follow us YouTube LinkedIn. In this test method, the shear characteristics are measured under undrained conditions and is applicable to field conditions where soils that have been fully consolidated under one set of stresses are subjected to a change in stress without time for further consolidation to take place undrained conditionand the field stress conditions are similar to those in the test method.
Installed on a PC communicating with the system over a fast Ethernet ashm, the software can be used to configure the system scalibrate transducers, specify test parameters, set This shear strength may be applied to field conditions where full drainage can occur drained conditions or where pore pressures induced by loading can be estimated, and the field stress conditions are similar to those in the test method.
ASTM D Standard
Soil mechanics – Dynamic triaxial systems: Specimens are isotropically consolidated and sheared in compression without drainage at a constant rate of axial deformation strain controlled.
In addition, they are representative of the significant digits that generally should be d47667. Reliable testing depends on several factors; Practice D provides a means of evaluating some of those factors. Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered standard.
Ast, technology is environmentally friendly and clean to operate, requiring no compressed air or hydraulic oil. All the data acquisition and test management are made in manual mode Power supply is only required for air compressor and for triaxial load frame during failure stage.
Standard triaxial system with built-in digital data acquisition Standard triaxial System with built-in data acquisition is the ideal compact solution for performing standard triaxial tests such as effective and total stress.
A typical Standard triaxial system with analogue measurements includes: A typical standard triaxial system with external data acquisition system includes: In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs.
Data are automatically transferred to the PC in real time for live plotting and monitoring of the tests in progress. Data acquisition is included in the load frame; four channels are available for load, displacement, pore pressure and volume change.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It offer excellent reliability, accurate testing and lower maintenance requirements.
This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. Three or six simple thumbscrew are used to clamp the upper part of the cell to the base, which make asstm and disassembly a very quick and Density is mass per unit volume whereas unit weight is force per unit volume.
Standard triaxial configuration with built-in data acquisition can be used for performing additional tests such as CBR, Unconfined and CRS. Please contact us for a complete offer. D7467 of this test method are cautioned that compliance with Practice D does not ensure reliable testing.
Aatm typical standard triaxial system with built-in acquisition measurement includes: Agencies which meet the criteria of Practice D are generally considered capable of competent testing. The shear strength of a saturated soil in triaxial compression depends on the stresses applied, time of consolidation, strain rate, and the stress history experienced by the soil.
Soil mechanics 4d767 Static triaxial systems: Introduced by the company over 50 years ago, they have undergone continuous development and are the ideal solution for advanced and research laboratories that want to perform high Using the pore-water pressure measured during the test, the shear strength determined from this test method can be expressed in terms of effective stress.
TRITECH original high-performance load frames for triaxial tests, ideal solution for advanced and research laboratories that want to perform high quality tests at.
Active Risk Management
Home Products Search results Results for: Work Item s – proposed revisions of this standard. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies or any consideration of end use.
The load frame is built around a robust d47767 column With this equipment it is possible to perform the consolidation stage of three triaxial specimens at the same time for CU and CD tests in anisotropic conditions.