This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D on Protective. ASTM D Standard Practice for Surface Cleaning Concrete for Coating. ASTM D (Plastic sheet test): Place plastic sheet on concrete stab for 24 hours. o ASTM-D Standard Practice for Surface Cleaning Concrete for.
|Published (Last):||4 June 2014|
|PDF File Size:||20.48 Mb|
|ePub File Size:||14.13 Mb|
|Price:||Free* [*Free Regsitration Required]|
You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. If the surface is new, test it for pH, many times the pH may be 10 or higher.
All loose mortar and foreign material should be removed from block. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. As the voice of the U. For concrete and steel substrates, a prepared surface is typically one that is clean, dry, structurally sound, and possesses a certain surface profile—the four pillars of good surface preparation.
ASTM D – 05() Standard Practice for Surface Cleaning Concrete for Coating
Need more than one copy? Standards Subsctiption may be the perfect solution.
Method of cleaning steel to remove dirt, oil, grease, loose rust, loose mill scale, and loose paint using water at pressures of 2, to 2, psi at a flow of 4 to 14 gallons per minute. The surface may be painted after 30 days if recommended procedures for applying stucco are followed, and normal d4285 conditions exist.
Bare plaster must be cured and hard before application.
Here is a summary of some of the published standards with which installers and specifiers of corrosion protection linings should be familiar. Remove all dust, oil, wax, grease, loose paint, mill scale, rust, dirt, mold, mildew, mortar, efflorensence, sealers, and other surface contaminants. Caulk should be applied after priming. Profiled Increasing the surface area of the substrate by imparting a profile with some tooth gives lining systems more to grab on to.
Prime and paint as soon as possible after surface prep.
This standard is also available to be included in Standards Subscriptions. Store finishing lumber and flooring in dry, warm rooms to prevent absorption of moisture, shrinkage, and roughening of the wood. Rinse carefully and allow to dry. astn
This method is suitable for removal of all visible oil, drawing and cutting compounds, grease, soil, and other soluble contaminants. If coating system is incompatible, complete removal of previous coating s is required per ASTMsee “Concrete Blast Cleaning ” above. You may delete a document from your Alert Profile at any time. When viewed without magnification, a White Metal Blast Cleaned surface should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, and other foreign matter.
So many corrosion protection lining projects succeed or fail with the quality of the surface preparation achieved before the lining is even installed. Thoroughly cleanse vinyl siding by scrubbing with a warm, soapy water solution.
If the document is revised or amended, you will be notified by email. As critical as these steps are, it should come as no surprise that there is a wealth of technical standards available from organizations such as NACEASTMand SSPC which address many aspects of steel and concrete surface preparation.
Mill scale and rust cannot be removed by solvent cleaning. Established by the Steel Structures Council inthese methods are used throughout the world for describing methods for cleaning structural steel. All loose rust, loose mill scale, loose and other detrimental foreign matter can be removed by power tool cleaning.
There was so much to do before I ever opened a can of paint. Spackle the drywall defects. If necessary, pressure clean with a minimum of psi to remove all dirt, dust, oil, grease, asrm, loose particles, foreign material, and peeling or defective coatings.
All nail heads must be set and spackled. Damaged areas must be repaired with an appropriate patching material.
Rinse thoroughly and allow to dry. Surface imperfections should be corrected and cleaned prior to painting.